Book Service Now

 

 

This great article down below involving How to Troubleshoot and Repair an Electric Water Heater is immensely captivating. You should check it out.

Several modern residences use an electric hot water heater for their heating unit, as a result of its convenience and also simplicity of use. However, much like any other electric home appliances, problems might occur with its use, suddenly. It can be actually frustrating to awaken to a chilly shower rather than a warm one or having your bathroom with water that isn't hot adequate and even too warm. Whatever the situation may be, water heater problems can be fairly stressful. Fortunately, we have actually made a list of feasible options to your water heater concerns. There are a number of factors that might trigger many of these issues, it could be a concern with the power supply, the electrical burner, or the thermostat. Before doing anything, guarantee you shut off the main power supply for security. Whatever the problem is, getting it taken care of ought to not posture excessive of a concern if you comply with these actions:

 

Check Your Power Supply:

As standard as this may appear, it is very needed. Without adequate power, your hot water heater will not work. So the first thing to do when your water suddenly stops working is to validate that it isn't a power problem. Inspect if the fuse is burnt out or the circuit breaker stumbled. If the circuit breaker is the problem, merely turn it on and off again. Replace any kind of broken or damaged fuse. Test the home appliance with power after these modifications to see if it's currently functioning.

 

Check the Burner in the Hot Water Heater:

If it's not a power problem, after that attempt having a look at your burner if it is still functioning. Evaluate each of your burner to be sure the problem isn't with any of them. If any one of them is faulty, replace that part and afterwards examine whether the hot water is back on.

 

Inspect Your Thermostat:

If your water heater still isn't functioning or the water appearing isn't warm sufficient, you might need to check the temperature settings on your upper thermostat. Make sure the breaker is turned off prior to doing anything. Open up the access panel and press the red button for temperature reset above the thermostat. This ought to help heat the water. Turn the circuit breaker back on and inspect if the issue has been fixed.

 

Call An Expert:

If after changing all malfunctioning components and also resetting your temperature level, the hot water heater still isn't functioning, you might require to call a specialist plumber for a professional opinion. The problem with your heater could be that the hot and cold taps have actually been changed or it might be undersized for the quantity of warm water required in your house. Whatever the instance might be, a professional plumber would certainly aid fix the issue.

 

Final thought

Water heater problems are not always significant. Most of them result from small problems like a blown fuse or worn-out heating element. Changing the malfunctioning components must work. Nevertheless, if you are still not able to resolve the issue, give a call to your nearest plumber to come to get it fixed.

 

What Would Cause My Electric Water Heater to Stop Working?

 

Your water heater is one of the most forgotten-about appliances in your home—until it quits working. Once you realize that there’s no hot water, the water heater jumps up to become the most noticeable appliance you have. No one in your family will be happy until you get the water heater fixed.

To fix an electric water heater as soon as possible, follow the troubleshooting advice discussed below.

 

Basic Water Heater Troubleshooting

 

Fortunately, you may be restore the hot water supply simply by resetting the house circuit breaker for the water heater. A tripped circuit breaker is one of the top causes of water heater failures. Shut the hot water heater breaker off then turn it back on. Give the water heater a half hour to heat up (if it’s working) and then check for hot water through one of your faucets.

If you get hot water after resetting the breaker, then the problem may be fixed if the breaker inadvertently tripped and it doesn’t continue tripping.

If the water heater breaker trips again, then you’ll likely need to have a service technician examine and repair the water heater. The service technician will check the circuit breaker and electrical supply wiring for the water heater. A short in the supply wiring or a bad circuit breaker could be causing the breaker to trip. An internal failure such as a broken heating element can also cause the breaker to continue tripping.

When resetting the water heater circuit breaker doesn’t work at all, then the water heater may be getting power while an internal water heater failure is causing the problem.

 

Conduct Advanced DIY Water Heater Troubleshooting

 

If the water heater doesn’t work after resetting the high-temperature limit switch, then you’ll need to either conduct some advanced water heater troubleshooting or have a service technician diagnose and repair the water heater failure.

Sears Technicians created a safe and highly-successful DIY advanced troubleshooting video to help you determine the cause of a water heating failure if you want to try to fix the problem yourself. Follow the advice in this video to find and fix the cause of the heating failure on your own:

 

The video begins with the basic troubleshooting described in the first 2 sections described above. It then goes on to guide you through checking water heater components to safely find the cause of the water heating failure.

If you get to a point in the troubleshooting where you’re not completely confident that you can safely continue, schedule a service technician to diagnose and repair the water heater.

The DIY water heater troubleshooting shown in the above video differs from the diagnosis techniques that service technicians typically use when examining a water heater to find the cause of a heating failure. Safe DIY troubleshooting doesn’t rely on live voltage checks while service technicians often use live voltage checks to quickly find the cause of water heater failures.

While many DIY’ers have been able to find the cause of water heater failures using troubleshooting advice shown in the video, some failures such as a bad circuit breaker can only be found using live voltage checks which should only be conducted by a trained service technician.

Sears Technicians have the training, tools and expertise to quickly find the cause of a water heater failure. Rely on our technicians to diagnose and repair your water heater or any other appliance in your home that quits working.

While the technician is in your home, take advantage of appliance Cleaning & Maintenance offers that the tech discusses with you. Keeping your appliances well-maintained will help them work more efficiently and last longer. Regular professional maintenance will also help prevent costly breakdowns of the appliances you depend on every day.

https://www.searshomeservices.com/blog/what-would-cause-my-electric-water-heater-to-stop-working

 

I have been very focused on How to Troubleshoot and Repair an Electric Water Heater and I hope you enjoyed reading the new post. If you liked our page plz don't forget to pass it around. We take joy in reading our article about What Would Cause My Electric Water Heater to Stop Working?.

Book My Estimate